AGILIS ACA de la Série en Bande C VSAT en plein air à Faible Bruit de Bloc de N de Sortie (LNB) | IK Tech Сorporation FR

Foxcom Platine à large bande PL7442T/PL7442R4 de la Liaison RF Large Plage de Puissance, 4dB Budget Optique à 8 km - 1310 nm ou 15 km - 1550 nm

Foxcom Platine à large bande PL7442T/PL7442R4 de la Liaison RF Large Plage de Puissance, 4dB Budget Optique à 8 km - 1310 nm ou 15 km - 1550 nm

Foxcom Platinum Wideband PL7442T/PL7442R4 RF Link Large plage de puissance, budget optique 4dB 8Km - 1310nm ou 15Km - 1550nm

• Large bande : 10–3000 MHz
• Plus de 8 Km. distance [15Km avec le PL7442T1550]
• De puissantes capacités de gestion via un écran LCD sur le panneau avant et un SNMP monté en rack
• Contrôle par l'utilisateur et réglage du niveau IMD requis
• Variété de connecteurs RF et optiques

    Foxcom Platinum Wideband PL7442T/PL7442R4 RF Link Wide Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm

     
    Summary
    Foxcom Platinum Wideband PL7442T/PL7442R4 RF Link Wide Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm Foxcom’s Platinum Wideband products are designed to meet the increasing demand for modularity and high-performance in a small form factor for superior long-distance transmission. With high RF input power and wide dynamic range, the link is designed to provide full specification service up to a full 4 dB optical budget with thePL7440R4 receiver. Utilizing Foxcom’s DigiRF technology, the user has full control of all important functions for setup, operation, and analysis via the front panel LCD or via the associated subrack SNMP capability. In addition IMizer, an automated adjustable link calibration embedded system enables the user to align the RF links IMD/CNR to specific linearity performances without a two-tone test. Select the desired IMD for the optical transmitter, either locally or remotely, IMizer automatically adjusts the laser drive to meet the IMD requirements. TheIMizer requires the use of a correction factor table above 2.5 GHz.  Each low profile individual transmitter or receiver can be “hot swapped” in the subrack chassis maintaining a best subsystem uptime capability. Each module contains an individual processor to maximize specification performance at all times under demanding user applications. The PL7440T transmitter and PL7440R4 receiver are designed for subrack chassis mounting. The associated Platinum chassis, model PL7010, has 12 active slots, one main control processor (MCP) slot and two redundant power supplies. No fans are required even under full subrack loading and full LNB powering.  
         
    Order Diagram - Options    

    Foxcom Platinum Wideband PL7442T / PL7442R4 RF Link Wide Power Range, 4dB Optical Budget 8Km - 1310nm or 15Km - 1550nm

     

    RF Specifications Units Typical Minimum Maximum
             
    Frequency Range - Bandwidth MHz 10 - 3000   3000
    Amplitude Response @ Unity Gain
    10 - 3000 MHz
    any 36 MHz
    dB
    ±2
    ±0.25    		  
    ±2.25
    ±0.3
    Gain Stability dB/24hr ± 0.2   ± 0.25
    Gain Slope1 dB 0 -1.5 +1.5
    Gain Variation over temperature dB ± 1.5 -2 2
    SFDR2 dB/Hz2/3 104    
    SFDR3 dB/Hz2/3 105    
    DR (Dynamic Range - single channel)4 dB     50
    CNR [1Hz]2 dB 133 130 135
    Noise Figure (NF)2 dB 37 42 35
    Noise Figure (NF)3 dB 16 19 14
    Output IP3 (OIP3)5 dBm 20    
    Group Delay Variation- linear
    10 to 60 MHz
    60 - 3000 MHz    		 ns
    13
    1.5    		  
    -15
    -11
    Input/Output Impedance Ohm 50 or 75    
    1 dB Compression Point dBm 2   3
    Phase Noise6 dBm None    
    Third Order InterModulation [IMD]4 dBc   -55 -40
    Input Signal Range - Total Power7 dBm   -50 0
    Maximum Input without Damage dBm     +15
    RF Output Signal Range - Total Power
    8
    9    		 dBm  
    -40
    -40
    +5
    +5
    TX/RX Input/Output Return Loss
    50 Ohm
    75 Ohm 13    		 dB
    -15
    -13    		  
    -15
    -11
    Test Port [front panel sample port]10 dB -20 -22 -18
    RF Connector Type
    Input/Output
    Test Port    		   SMA, N
    BNC    		  
             
             
    Optical Specifications  Typical Minimum Maximum
             
    Optical Wavelength nm 1310/1550/CWDM    
    Optical Power Output mW / dBm 2 / 3 1.7/2.5  
    Optical Budget / Distance
    4 dB optical budget    		 dBm/Km 1310 nm | 1550 nm
    8 |15    		    
    RX Optical Input Power dBm -1 -2 4
    Optical Connector Types Type FC/APC or SC/APC
    (E2000 option)    		 -  
    Optical Return Loss dB   -60 -55
    Electrical Specifications        
    Supply Voltage Vdc 12    
    Supply Current [TX]11 Amps 0.5    
    Supply Current (RX) Amps 0.45    
    EMI Rating   EMI Rating: FCC Class B
    CE Mark    		    
           
    Physical Specifications       
             
             
    Operating Temperature Range ºC   -10 +55
    Storage Temperature Range ºC   -45 +85
    Relative Humidity   95% non-condensing    
    Altitude ft / Km 10,000 [3.08 ] operating12
    14,000 [12.2] non-operating    		    
    Dimensions [D×W×H] ins/cm 12×0.8×4 / 30.5×2×10.2    
    Weight lbs./Kg 0.5 / 0.23    
    MTBF Hours TX: 309, 481
    RX: 359, 057    		    
    MTTR Hours 0.083    
    Shock & Vibration  

    Designed for normal transportation environment per section 514.4 MIL-STD-810E. Designed to withstand 20G at 11 ms [½ sine pulse] in non-operating configuration.