Foxcom Platinum Wideband PL7440DT DWDM [10 dBm laser]
![Foxcom Platinum Wideband PL7440DT DWDM [10 dBm laser]](/site/v1/uploads/products/img/192.jpg?8 "Foxcom Platinum Wideband PL7440DT DWDM [10 dBm laser]")
Foxcom Platinum Wideband PL7440DT DWDM [10 dBm laser]
• Supports 10mW High power CWDM and DWDM butterfly-type lasers• Wideband: 10–3000 MHz
• Powerful management capabilites via a front panel LCD and rack mounted SNMP
• User control and setting of required IMD level
• Variety of RF and optical connectors
Foxcom Platinum Wideband PL7440DT DWDM [10 dBm laser]
Summary |
||
|
Foxcom PlatinumWideband PL7440DT DWDM [10 dBm laser] Foxcom’s Platinum PL7440DT DWDM Wideband Transmitter is designed to meet the increasing demand for superior long-distance transmission with High CNR. With high RF input power and wide dynamic range, the Transmitter is designed to provide full specification service up to a full 32 dB optical budget with the PL7220R25receiver. Utilizing Foxcom’s DigiRF technology, the user has full control of all-important functions for setup, operation, and analysis via the front panel LCD or via the associated subrack SNMP capability. Each low profile individual transmitter or receiver can be “hot swapped” in the subrack chassis maintaining a best subsystem uptime capability. Each module contains an individual processor to maximize specification performance at all times under demanding user applications. The PL7440DT transmitter is a compatible Platinum chassis mounted device. The associated Platinum chassis, model PL7010, has 12 active slots, one main control processor (MCP) slot and two redundant power supplies. No fans are required even under full subrack loading and full LNB powering.
|
||
| Order Diagram - Options | ||
Foxcom Platinum Wideband PL7440DT DWDM [10 dBm laser]
| RF Specifications | Units | Typical | Minimum | Maximum |
| Frequency Range - Bandwidth | MHz | 10 - 3000 | ||
| Amplitude Response @ Unity Gain 10 - 3000 MHz any 36 MHz |
dB |
±2 ±0.2 |
±2.25 ±0.3 |
|
| Gain Stability | dB/24hr | ± 0.2 | ± 0.25 | |
| Gain Slope | dB | 0 | -1.5 | +1.5 |
| Gain Variation over temperature | dB | -2 | 2 | |
| SFDR1 | dB/Hz2/3 | 90 | ||
| DR (Dynamic Range - single channel)3 | dB | 50 | ||
| CNR [any 36 MHz]1 | dB | 37 | ||
| Noise Figure (NF)1 | dB | 41 | ||
| Noise Figure (NF)2 | dB | 20 | ||
| Output IP3 (OIP3)4 | dBm | -5 | +20 | |
| Group Delay Variation- linear 10 to 60 MHz 60 - 3000 MHz |
ns |
13 1.5 |
||
| Input/Output Impedance | Ohm | 50 or 75 | ||
| 1 dB Compression Point5 | dBm | 3 | 11 | |
| Phase Noise6 | dBm | None | ||
| Third Order InterModulation [IMD]3 | dBc | -55 | -40 | |
| Input Signal Range - Total Power7 | dBm | -50 | 0 | |
| Maximum Input Without Damage | dBm | +15 | ||
| TX/RX Input/Output Return Loss 50 Ohm 75 Ohm9 |
dB |
-15 -13 |
-15 -11 |
|
| Test Port [front panel sample port]8 | dB | -20 | -22 | -18 |
| RF Connector Type Input/Output Test Port |
F, SMA, N F, BNC |
|||
| Optical Specifications | Typical | Minimum | Maximum | |
| Optical Wavelength | nm | DWDM/CWDM | ||
| Optical Power Output | mW / dBm | 6 / 10 | ||
| Optical Budget / Distance | dBm/Km | Depends on receiver sensitivity | ||
| Optical Connector Types | Type | FC/APC or SC/APC (E2000 option) |
- | |
| Optical Return Loss | dB | -60 | -55 | |
| Electrical Specifications | ||||
| Supply Voltage | Vdc | 12 | ||
| Supply Current [TX]7 | Amps | 0.5 | ||
| EMI Rating | FCC Class B CE Mark |
|||
| Physical Specifications | ||||
| Operating Temperature Range | ºC | -10 | +55 | |
| Storage Temperature Range | ºC | -45 | +85 | |
| Altitude | ft / Km | 10,000 [3.08 ] operating8 14,000 [12.2] non-operating |
||
| Dimensions [D×W×H] | ins/cm | 12×0.8×4 / 30.5×2×10.2 | ||
| Weight | lbs./Kg | 0.8 / 0.23 | ||
| MTBF | Hours | TX: 309,481 | ||
| MTTR | Hours | 0.083 | ||
| Shock & Vibration | Designed for normal transportation environment per section 514.4 MIL-STD-810E. Designed to withstand 20G at 11 ms [½ sine pulse] in non-operating configuration |
|||