AGILIS ACA de la Série en Bande C VSAT en plein air à Faible Bruit de Bloc de N de Sortie (LNB) | IK Tech Сorporation FR

Foxcom Platine Bande L PL7230T [PL7230T1550 ]/PL7230R4 de liaison Montante Haute Puissance d'Entrée, 4 dB Budget Optique

Foxcom Platine Bande L PL7230T [PL7230T1550 ]/PL7230R4 de liaison Montante Haute Puissance d'Entrée, 4 dB Budget Optique

Foxcom Platinum L-Band PL7230T [PL7230T1550 ]/PL7230R4 Entrée haute puissance UpLink, budget optique de 4 dB

• Bande L : 950 – 3000 MHz
• Plus de 8 km [15 km avec le PL7230T1550]
• De puissantes capacités de gestion via un écran LCD en façade et un SNMP monté en rack
• Contrôle utilisateur et réglage du niveau IMD requis
• Contrôle de la puissance LNB via LCD ou SNMP : +13 ou 18 VDC

    Foxcom Platinum L-Band PL7230T [PL7230T1550 ]/PL7230R4 UpLink High Power Input, 4 dB Optical Budget

     
    Summary
    Foxcom L-Band PL7230T [PL7230T1550 ]/PL7230R4 UpLink High Power Input, 4 dB Optical Budget Foxcom’s Platinum L-band products are designed to meet the increasing demand for modularity and high-performance in a small form factor for superior long-distance transmission. With high RF input power and wide dynamic range, the link is designed to provide full specification service up to a full  4dB optical budget with thePL7230R4 receiver . Utilizing Foxcom’s DigiRF technology, the user has full control of all important functions for setup, operation, and analysis via the front panel LCD or via the associated subrack SNMP capability. In addition IMizer, an automated adjustable link calibration embedded system enables the user to align the RF links IMD/CNR to specific linearity performances without a two-tone test. Select the desired IMD for the optical transmitter, either locally or remotely, IMizer automatically adjusts the laser drive to meet the IMD requirements. TheIMizer requires the use of a correction factor table above 2.5 GHz.  Each low profile individual transmitter or receiver can be “hot swapped” in the subrack chassis maintaining a best subsystem uptime capability. Each module contains an individual processor to maximize specification performance at all times under demanding user applications. The PL7230T transmitters and the PL7230R4 receiver is designed for chassis mounting. The associated Platinum chassis, model PL7010, has 12 active slots, one main control processor (MCP) slot and two redundant power supplies. No fans are required even under full subrack loading and full LNB powering.  
         
    Order Diagram - Options    

    Foxcom Platinum L-Band PL7230T [PL7230T1550 ] / PL7230R4 UpLink High Power Input, 4 dB Optical Budget

     

    RF Specifications Units Typical Minimum Maximum
             
    Frequency Range - Bandwidth MHz 950 - 3000   -
    Amplitude Response @ Unity Gain
    950–3000 MHz
    any 36 MHz
    dB
    ±1.25
    ±0.2    		  
    ±1.5
    ±0.25
    Gain Stability dB/24hr ±0.2   ± 0.25
    Gain slope1 dB   -1.0 +1
    Gain Variation over temperature dB   -2 2
    SFDR2 dB/Hz2/3 105    
    SFDR3 dB/Hz2/3 104    
    DR (Dynamic Range - single channel)4 dB     30
    CNR [any 36 MHz]3 dB 53   53
    Noise Figure (NF)2 dB 30 28 33
    Noise Figure (NF)3 dB 10 9 12
    Output IP3 (OIP3)5 dBm - 15 20
    Group Delay Variation- linear @
    950 to 1200 MHz
    1200 to 3000 MHz    		 ns
    3
    1.5    		    
    Input/Output Impedance Ohm 50 or 75    
    1 dB Compression Point dBm 2   3
    Phase Noise6 dB None    
    Third Order InterModulation [IMD]7 dBc   -55 -40
    RF Input Signal Range - Total Power dBm   -30 -5
    Maximum input without damage       +15
    Output Signal Range - Total Power8 dBm   -30 -5
    TX/RX Input/Output Return Loss
    50 Ohm
    75 Ohm9    		 dB
    -15
    -13    		  
    -15
    -11
    Test Port [front panel sample port]10 dB -20 -22 -18
    RF Connector Type
    Input / Output
    Test port    		  
    align=center>F, SMA, BNC, N
    F, BNC
             
             
    Optical Specifications   Typical Minimum Maximum
             
    Optical Wavelength nm 1310/1550/CWDM    
    Optical Power Output mW/dBm 2 / 3 1.7/2.5  
    Optical Budget / Distance
    4 dB optical budget    		 Km 1310 nm | 1550 nm
    8 | 15    		    
    RX Optical Input Power dBm
    -1
    -2    		 4
    Optical Connector Types Type FC/APC or SC/APC
    (E2000 option)    		    
    Optical Return Loss dB   -60 -55
             
             
    Electrical Specifications        
             
    Supply Voltage Vdc 12    
    Supply Current 11
    TX, No LNB
    TX with LNB    		 Amps
    0.45
    0.75    		    
    EMI Rating   EMI Rating: FCC Part 15 Class B
    CE Mark    		  
         
         
    Physical/Environmental Specifications      
             
    Operating Temperature Range ºC   -10 +55
    Storage Temperature Range ºC   -45 +85
    Relative Humidity   95% non-condensing    
    Altitude ft / km

    10,000 [3.08 ] operating12
    14,000 [12.2] non-operating

    		    
    Dimensions [D×W×H] ins/cm 12×0.8×4 / 30.5×2×10.2    
    Weight lbs./Kg 0.5 / 0.23    
    MTBF Hours TX: 309,481
    RX: 359,057    		    
    MTTR Hours 0.083    
    Shock & vibration Designed for normal transportation environment per section 514.4 MIL-STD-810E. Designed to withstand 20G at 11 ms [½ sine pulse] in non-operating configuration
             
    1.   Within flatness spec
    2.   -5 dBm RF input, link gain = 0 dB, IMD=-40 dBc @ 0 dBm optical input - max. RF input
    3.   -30 dBm RF input, link gain =25 dB, IMD=-40 dBc @ 0 dBm optical input - min. RF input  
    4.   User adjustable
    5.   -5 dBm RF in @ IMD=-40 dBc
    6.   Direct modulation utilized
    7.   Adjustable. Above -10 dBm input min. -50 dBc
    8.   Alarm trip point: RED -2 dBm, AMBER -33 dBm
    9.   -15 dB @ 950 to 3000 MHz, -11 dB @ 2500 to 3000 MHz
    10.   -45 dBm minimum input
    11.   Under 10º add 120 mA for Tx [laser heating]
    12.   WIth standard adiabatic derating at 2ºC/1000ft. [0.3 Km.]